Hornady New Dimension Expander Dies Manuel d'utilisateur
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Hornady New Dimension Expander Dies. Hornady New Dimension Expander Dies User Manual Manuel d'utilisatio
- Page / 1
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Before using your new die, it must be thoroughly cleaned. A rust
preventative is applied at the factory and must be removed before
using the die. We recommend Hornady One Shot Cleaner and Dry lube
or any commercial solvent will suffi ce. The expander die is designed to
put a slight “bell” or fl are on the case mouth. For uniform fl aring trim
all cases to proper length.
To adjust the expander die, fi rst place a case in the shell holder and
raise the ram to full extension. Thread the expander die into the press
until the expander touches the case mouth. Raise the handle and
screw down the die in quarter-turn increments, each time inspecting
the case mouth, until the mouth of the case has been fl ared just
enough to start a bullet into the case mouth. Tighten the lock ring
against the press, and lock it in place with the set screw. Keep in
mind that excessive fl are can eventually shorten case life, and may
keep the case from properly entering the seating die.
Item 780150
NEW DIMENSION
EXPANDER DIE
3625 Old Potash Hwy • P.O. Box 1848 •
Grand Island, NE 68802
308-382-1390 • www.hornady.com
Before using your new die, it must be thoroughly cleaned. A rust
preventative is applied at the factory and must be removed before
using the die. We recommend Hornady One Shot Cleaner and Dry lube
or any commercial solvent will suffi ce. The expander die is designed to
put a slight “bell” or fl are on the case mouth. For uniform fl aring trim
all cases to proper length.
To adjust the expander die, fi rst place a case in the shell holder and
raise the ram to full extension. Thread the expander die into the press
until the expander touches the case mouth. Raise the handle and
screw down the die in quarter-turn increments, each time inspecting
the case mouth, until the mouth of the case has been fl ared just
enough to start a bullet into the case mouth. Tighten the lock ring
against the press, and lock it in place with the set screw. Keep in
mind that excessive fl are can eventually shorten case life, and may
keep the case from properly entering the seating die.
Item 780150
NEW DIMENSION
EXPANDER DIE
3625 Old Potash Hwy • P.O. Box 1848 •
Grand Island, NE 68802
308-382-1390 • www.hornady.com
Before using your new die, it must be thoroughly cleaned. A rust
preventative is applied at the factory and must be removed before
using the die. We recommend Hornady One Shot Cleaner and Dry lube
or any commercial solvent will suffi ce. The expander die is designed to
put a slight “bell” or fl are on the case mouth. For uniform fl aring trim
all cases to proper length.
To adjust the expander die, fi rst place a case in the shell holder and
raise the ram to full extension. Thread the expander die into the press
until the expander touches the case mouth. Raise the handle and
screw down the die in quarter-turn increments, each time inspecting
the case mouth, until the mouth of the case has been fl ared just
enough to start a bullet into the case mouth. Tighten the lock ring
against the press, and lock it in place with the set screw. Keep in
mind that excessive fl are can eventually shorten case life, and may
keep the case from properly entering the seating die.
Item 780150
NEW DIMENSION
EXPANDER DIE
3625 Old Potash Hwy • P.O. Box 1848 •
Grand Island, NE 68802
308-382-1390 • www.hornady.com
Before using your new die, it must be thoroughly cleaned. A rust
preventative is applied at the factory and must be removed before
using the die. We recommend Hornady One Shot Cleaner and Dry lube
or any commercial solvent will suffi ce. The expander die is designed to
put a slight “bell” or fl are on the case mouth. For uniform fl aring trim
all cases to proper length.
To adjust the expander die, fi rst place a case in the shell holder and
raise the ram to full extension. Thread the expander die into the press
until the expander touches the case mouth. Raise the handle and
screw down the die in quarter-turn increments, each time inspecting
the case mouth, until the mouth of the case has been fl ared just
enough to start a bullet into the case mouth. Tighten the lock ring
against the press, and lock it in place with the set screw. Keep in
mind that excessive fl are can eventually shorten case life, and may
keep the case from properly entering the seating die.
Item 780150
NEW DIMENSION
EXPANDER DIE
3625 Old Potash Hwy • P.O. Box 1848 •
Grand Island, NE 68802
308-382-1390 • www.hornady.com
1
Résumé du contenu
Page 1 - Item 780150
Before using your new die, it must be thoroughly cleaned. A rust preventative is applied at the factory and must be removed before using the die. We r
Produits connexes et manuels pour Matériel Hornady New Dimension Expander Dies
(3 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.835 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels